Markets face a Hobart 140 Vs. Lincoln 140 decision for a good quality 140 amp MIG welder. Home and small businesses can take these two products into account, being first-time beginners with no worry about names. Hobbyists choosing either will get commendable consequences as they are one of the most trusted brands.
Hobart 140 and Lincoln 140 come on the same page about building quality and specs. You cannot go wrong once you invest in any of them. Till now, both came out to be a better choice or best fit in subtle experiences.
Now the question is, what makes them different? Let us find out with a logical comparison.
Hobart 140 Vs Lincoln 140 Comparison TableInvalid table id.
Hobart 140 Vs. Lincoln 140
Usually, we concern ourselves most with reliability. To be, it’s operating or controlling, both the machines compile a control panel with an on/off switch. Wire feed speed changes are inclusive here, with two knobs for voltage. Moreover, the power switches are rocker style and glove-friendly.
Five-position voltage control is a mere adjustment in Hobart 140. After adequate research on the Lincoln 140 review, we found that this product uses four heat levels. So it would help if you relied on WFS adjustment as voltage can’t be used on a fine tune with stepped settings.
On the other hand, Hobart 140 review proclaims it as a closer to ideal heat setting. Fine-tune wire spreads are not that essential here in order with smooth functions.
Ideal wire-speed varies due to sticking out, weld angle, travel speed, etc. But if you go for weld parameter charts, they are generally more accurate. While Hobart 140 will give you more flexibility on its behalf with an extended range for aluminum work.
When you dial the process correctly, it will be almost impossible to click out any differences. So, which one directly implies to your convenience, choose that one.
Quick Comparison Chart
|Features||Hobart 140||Lincoln 140|
|Process||MIG, Flux Core||MIG, Flux Core|
|Duty cycle||20% @ 90A (18.5V)||20% @ 90A (19.5V)|
|Input voltage||110V / 115V / 120V (20A)||110V / 115V / 120V (20A)|
|Wire feed speed||40 – 700 imps||50 – 500 imps|
|Voltage control||5 fixed position||4 fixed position|
|Materials||Stainless, aluminum, mild steel||Stainless, aluminum, mild steel|
|Spoon gun capable||Have||Does not have|
|Amperage range||25 – 140 A||30 – 140 A|
|Mild steel thickness||24 Ga. – 3/16 in.||24 Ga. – 3/16 in.|
|Weight||57 lbs||50 lbs|
Hobart 140 Vs. Lincoln 140: The Breakdown
A little discussion is not enough when it’s about handling your business in purchasing a MIG welder. On that note, I have amalgamated some important traits on Lincoln 140 vs. Hobart 140 to make you more clear.
Both the manufacturers equipped calibrated tension control and tool-less drive roll changes. Each of them got functional reliability with an aluminum wire drive.
There are two groove rollers in the Lincoln 140 MIG welder. One handles 0.25 solid wire, and the other handles 0.30/0.35 solid wire. You can also say they work exceptionally as flux cores because of fewer changes. It is a very easy tool but requires frequent removal of the drive roll to flip around.
In contrast, the Hobart quick select system is user-friendly and features a triple groove drive roller. They are better thought out due to faster wire changes. You are to twist to align the pin with wire type by pushing inside and then release. Moreover, there is no need to remove the roller in these three grooves.
Two smooth grooves of 0.024 solid wire and 0.030 / 0.035 flux core wire. You will get a good grip on soft wire with the help of an extra 0.030 / 0.035 knurled groove. The lighter roller tension settings remove squeezing or deforming problems of wire feeds.
If you rate the Hobart handler 140 vs. Lincoln 140, you will get 12 to 16 gauge in Hobart’s wire drive system. There is a reason most manufacturers do not recommend Lincoln because it lacks in pushing soft aluminum wire at high speed.
While testing on aluminum, Hobart 140 and its wire drive system works great comparing to Lincoln.
Both the machines have reliable and strong wire feed systems and can be expected for a trouble-free welding experience. But if you look for more range of adjustments and easy use, Hobart is finer, allowing light-duty aluminum work.
Each welder is involved with a good quality brass regulator and dual gauges. You will need a dial marked in cubic feet/hour (CFH) for making adjustments to monitor gas flow. In the second dial, gas cylinder pressure is displayed per square inch (PSI). By this, you will be shown how much gas volume is remaining.
Lincoln 140 includes Harris regulator, and Hobart regulator includes miller brands. Whereas 100% Argon and Argon blend like C25 MIG-mix doesn’t allow 100% CO2 gas in Hobart. But if you consider Lincoln’s regulator, they work with 100% CO2 gas, which is less expensive.
Cables / Gun
Both welders consist of 10 foot MIG comfortable guns and easy handling work cables. Two of them cover quality with heavy six gauge ground levels, but Hobart skimps on the work clamp. The gauges are small here and don’t combine with the bonding cable.
On the other side, Lincoln 140 brings the jaws together and forms a bond with braided wire. There is no deficiency in making good circuits even though it makes better contact with work materials. That’s because the current does not follow the hinge or spring and travels through the bonding cable.
Crucial problems are far from Hobart 140 except for its small size having a cheap and easy fix. But that’s not sufficient. We want a solid at the top jaw as well. In such situations choosing Lincoln 140 would be a very sensible option since it acquires a true heavy-duty clamp.
140 amp welders of Lincoln vs. Hobart have a similar design of three-level protection.
- Wire drive motor protection: Both machines have separate automatic overload circuits to protect their wire drive motors.
- Output overload: The welders can be damaged if they exceed their maximum output. For this, a manual reset table circuit breaker is installed to protect them.
- Thermal protection: Welders overheat when they exceed the normal duty cycle. An automatic thermostat in these two products protects the power transformer and prevents further welding.
Duty cycles are provided to see how long a welder operates at its certain power of output level. Both our welders contain the same duty cycle of 20% @ 90A seeming 110V MIG. They will tell you about the 10 minutes when producing 90 amps of output. The exemplary operation they obtain is 2 minutes, and the rest 8 minutes is for cooling down.
Here, the award goes to Hobart 140 for its good providence of light to show the front panel’s temperature condition. This way, it illuminates the machine within thermal protection mode and shuts off when welding is ready.
But the Lincoln welder doesn’t give any overload confirmation and makes you unsure if you should pull the trigger. Now the concept is getting more engrossing; who will win in Hobart 140 Vs. Lincoln 140.
Warranty differs for the tipping point. Lincoln’s labor warranty and three-year parts protect it’s a series welder. The MIG gun consoles for 90 days with an applied exclusion, and the gas regulator lasts one year. Furthermore, wear and tear need no coverage on cables.
Parts and labor coverage features come with five years on the power source transformer of Hobart 140. Then the drive system, regulator, and control boards abided for three years. Lastly, the cover of MIG guns and contractors continues to exist for one year. And if you think for industrial use, it will remain for 90 days.
On a juxtaposition of both the products, Hobart wins the advantage of the warranty. But there is no doubt that Lincoln provides solid coverage. So, snap up that one that is similar to your choice.
# Hobart 140 Welder
Pros of Hobart 140
- Wire feed system handles feed wires up to 700 inches per minute even at difficult times
- Doesn’t need any expensive accessories while welding aluminum
- Has a fine-tuned heat of 5 position voltage control
- Convenient for Quick Select Drive roller within a triple groove
- User-friendly item
- Transformer warranty is applicable for five years
- Shows over-temperature conditions
- Consumes ideal heat settings
- Assembled in the United States
Cons of Hobart 140
- There is no option for spool gun
- CO2 shielding gas rejects to use regulator
- Small work clamp without any heavy duty
- Aluminum works are difficult to do with this welder
# Lincoln 140
Pros of Lincoln 140
- It has a ready spool gun
- Work clamp is heavy duty
- Consists of a bonding strap between the jaws
- Wire spool does not need any tools
- Provides wire drive and polarity changes
- Has strong wire feed system
- Designed with true heavy-duty clamp
- A better welder for aluminum works
Cons of Lincoln 140
- Aluminum weld does not work without an optional spool gun
- No more assembling is done in the USA
- Warranty is less compared to Hobart
- Voltage settings have only 4 position
- Doesn’t give overload conformations
If you avoid aluminum projects, choosing from Hobart 140 Vs. Lincoln 140 shouldn’t be difficult for you. Recently, Hobart handler 140 won over Lincoln for its best 110 volt MIG welders.
Both welders relate for their dependable and portable uses. And if you ate a beginner, then it’s going to be very easy for you to use. We know wire drive is the heart of welders, which is evident in Hobart 140.
Additionally, if you are concerned about the warranty, even that is accountable from Hobart. But for better aluminum works, Lincoln 140 will be a good choice. So, make your acquisition wisely and have a nice experience with your favorite MIG welder.